| | |  | Tubing Tools | Home » » 10-pc. Double Flaring Tool Set | | | | | | | Description: | | Specifications:
? Chrome Plated Steel Die Bars
and Clamping Screws
? Drop Forged, Heat-Treated Steel Yoke
? Hardened, Self-Centering Cone
Produces Perfect 45 Flares
? No Wrench Needed - Sliding T-Handle
Provides Necessary Torque
? Die Bars Have a Hinged Design and
Wing-Nut Clamping Screws
Contents:
? 7pc. Double-Flare Adapters:
3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8"
? 1pc. Hinged Die Bars:
Threaded Die Sizes:
3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8"
? 1pc. Flaring Yoke
? 1pc. Molded Plastic Carry Case | | | Features: | |
• Precision-machined steel die bar and double flare adapters
• Hardened center screw with sliding t-bar handle
• Produces 45 degree flare angle
• Use with copper, aluminum, and thin-walled steel tubing
• Ideal for water, gas, refrigeration, and brake line applications
| | | Product Details: | | | Product Length:
| 7.0 inches | | Product Width:
| 9.0 inches | | Product Height:
| 2.0 inches | | Product Weight:
| 2.63 pounds | | Package Length:
| 9.4 inches | | Package Width:
| 7.4 inches | | Package Height:
| 2.1 inches | | Package Weight:
| 2.6 pounds | | Average Customer Rating:
|  based on 6 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 6 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
3 of 3 found the following review helpful:
 disappointedFeb 15, 2010
By Dan
The swivel is not chromed as in the picture, it is black oxide. The clamp was not able to hold the tubing to produce even a single flare, the "threading" in the tubing clamp(which grips the tubing to hold it) stripped out after a few attempts to flare some tubing. No matter how tight I secured the tubing in the clamp, it would not hold the tubing in place to create a flare.
1 of 1 found the following review helpful:
 Double Flares &uckMar 30, 2012
By Dave Wissel
So you think you can use one of these tools to double flare small brake line? After you use it, you will know why Advance and Autozone sells tons of brake line--cause you'll end up blowing lots of line on bad flares. In the end you WON"T end up with a perfect flare--just a so so lop-sided one if you're lucky. Far better to take your line to a fellow with a pro flare tool and have them do it. The NEXT best is to use a BUBBLE FLARE tool which you can find on Amazon for same price anyway. Many cars actually have BUBBLE flares and NOT double flares and NO...Autozone is WRONG when they tell you a Bubble is a Double. The BUBBLE flares are easier to do and only need ONE flaring operation. The tools are better as the ANVILS are better.
Ok...so now you understand that, I'll tell you how to get as close as possible to a good flare. The problem isn't necessarily the tool--its the slight off alignment of the tube in the vice. If its even slightly off 'square", when you drop the anvil down, it will smash it lop sided. Ok, so here is my trick. Put the tube in the vice first nearly FLUSH with the vice surface and tighten the heck out of the vice. This will straighten it. While there, file it flat to the top. Now move the tube into the proper height for the first flare and chamfer the edge a little. Now flare it. Oh and by the way, the way to tighten the vice is this way: (1) Loosen all screws. (2) Tighten the screw nearest the tube all the way (3) Tighten the far away one all the way. Now it is squeezed in the fulcrum of the vice.
1 of 1 found the following review helpful:
 It did a partial jobOct 26, 2011
By J. F. Vogel
"Road Runner"
I rated this flairing kit 4 stars. I the storing case is excellent..holds the pcs that it takes to flare any size of line . The downside of this kit was the flaring clamp screw. After the second attempt to do a double flair the tip of the flaring screw was ruined. Even with lubricating oil it still failed. Even tho the tip is ruined, I will use the rest of the pieces with another flaring tool I have.
Not a good purchaseMar 18, 2012
By keith
Honestly, this was my first time doing brake lines but I am very handy and watched a few videos on youtube from guys who knew what they were doing. I was unable to make even one double flare with this tool without having to fix the tool. The flaring cone is made of soft metal that deformed (squashed the point) on the first try of pushing the die into the 3/16" line. I had to file the point down to finish the flare. On the second try, one of the wing nuts broke right off so I had to secure the holder in a vise. This tool is junk - nice box though.
 Did the jobAug 13, 2011
By Eaglesfan
This is the first time using this type of tool, I did complete the job but I noticed while flaring the tube the part that flares the tube would go at a angle making it a lop sided flare. I did tighten it down really good, It just took a few tries to get it right. If needed again I would prob buy a more expensive set hoping for better quality.
See all 6 customer reviews on Amazon.com
| | |
|
